ISO INTERNATIONAL STANDARD 9445-2 First edition 2009-03-01 Continuously cold-rolled stainless steel Tolerances on dimensions and form - Part 2: Wide strip and plate/sheet Acier inoxydable lamine a froiden continu-Tolerances surles dimensions etlaforme Partie2:Largesbandesettoles Reference number ISO 9445-2:2009(E) @ISO2009 ISO9445-2:2009(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation COPYRIGHTPROTECTEDDOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, ISO's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. :+ 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ISO9445-2:2009(E) Contents Page Foreword iv 1 Scope 2 Normative references.... 3 Terms and definitions... 4 Informationtobesuppliedbythepurchaser 5 Type of delivery and delivery condition.... 6 Preferred thicknesses. 3 7 Tolerances on thickness forcold-rolledwide stripandproducts obtainedfrom cold-rolled wide strip.... 8 Tolerances on width for cold-rolled wide strip and products obtained from cold-rolled wide strip ..... 9 Preferred coil inner diameters for cold-rolled wide strip and slit cold-rolled wide strip .... 10 Tolerances on length for plate/sheet cut from cold-rolled wide stripand for cut lengths obtained from slit cold-rolled wide strip ... 11 Tolerances on edge camberfor cold-rolled wide strip and products obtained from cold- rolled wide strip ... 12 Tolerances on squareness forplate/sheet obtained from cold-rolled wide strip and cut lengths obtained fromslit cold-rolled wide strip ... 13 Tolerances on flatness forplate/sheet obtainedfrom cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip ... 14 Edge waviness tolerances for cold-rolled strip. 15 Form of coils. 16 Orderedformat forplate/sheet and cut lengths. 17 Measurement of thickness for cold-rolled wide strip, plate/sheet cut from cold-rolled wide strip, slit cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip...... 18 Measurement of width. 8 19 Measurement of length.. 8 20 Measurement of edge camber. 21 Measurementof squareness 22 Measurementofflatnessandwaviness ISO9445-2:2009(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through IsO non-governmental, in liaison with isO, also take part in the work. isO collaborates closely with the International Electrotechnical Commission (IEC)onall matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 9445-2 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 4, Heat treatable and alloy steels. This first edition of ISO 9445-2, together with IsO 9445-1